|
Latchways ManSafe® Fall Protection System
|
|
Latchways cable based ManSafe® systems range from a single cable across an industrial unit roof to a complete network of systems enabling safe cleaning, maintenance, access and inspection. The unique Transfastener TM, attaching the user to the system, incorporates a patented starwheel design which allows the user continuous movement along the cable without the need to detach.
The systems are usually designed for 2 workers to be attached at any one time, but greater loads can be accommodated if necessary.
End anchors are made from stainless steel and use either a single M16 or 2 M12 fixing bolts. Typical end anchor loadings are 10 – 15kN, but can be further controlled through the spacing of intermediate brackets and the inclusion of inline energy absorbers. System design must be verified by the Latchways software programme.
System support brackets made from 316 marine grade stainless steel can be fixed into virtually any structure, including masonry, brick and blockwork and structural steel.
The intermediate brackets use a single M12 fixing point, and are usually spaced approximately 6 – 10 metres apart, depending on system design. The Transfastener passes freely over the intermediate supports, keeping the user attached at all times.
Consult Latchways technical literature for details. Latchways plc can also provide a specification service mailto:%28spec@latchways.com) and it is recommended that they are consulted early in the design process.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
System reference: Latchways ManSafe® Fall Protection System
|
|
Latchways ManSafe® for Metal Profiled Roofin
g
|
|
Designed specifically for built up on site and composite roof applications where a 8mm 7x7 316 grade stainless steel cable system is mounted at ankle height.
Anchorage device: Latchways Constant Force™ Post for mechanical attachment to the top skin of the profile using 16 Latchways stitching screws per post. The use of simple weather tight stitching screws allows the system to be located anywhere on the roof between two crowns. The post is powder coated in Goosewing grey or neutral silver as standard and contains an integral energy absorber, which deforms at a constant force in the event of a fall to prevent damage to the roof panel. Posts must be installed between 6 and 10 metres apart to guarantee a maximum load of 10kN onto the roof. The use of both internal and external corner units provide greater system flexibility.
Overall system length: This should comprise the roof perimeter system and single runs to allow access to gutters. Indicate if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Intermediate support spacing: Between 6 and 10m - as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Consult Latchways technical literature for details. Latchways plc can also provide a specification service mailto:%28spec@latchways.com) and it is recommended that they are consulted early in the design process.
It is recommended that the following clauses should also be included in the NBS specification for this system. N25/430, 460, 510, 520, 530, 550, 560, 570, 610, 640, 820 and 830.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
System reference: 210 Guided Type Fall Arrest System; Latchways ManSafe® for Built-up on Site and Composite Panel Metal Profiled Roofing.
Anchorage device: Latchways Constant Force™ Post
Finish: Polyester powder coated. Colour: Goosewing Grey / Neutral Silver
Attachment: Mechanical attachment to the top skin of the profile using 16no. Latchways stitching screws per post.
Overall system length: Specify length of system in metres comprising roof perimeter system and single runs to allow access to gutters. Specify if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Consult with Latchways for recommendations and details.
Intermediate support spacing: Between 6 and 10m and as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Accessories/ Other requirements:
System access: To be from … Consult with Latchways for recommendations and complete accordingly.
Completion: On completion of the installation, system to be inspected and fully tested and a test certificate covering a period of 12 months to be issued. Notice showing date and period of validity of the test certificate to be attached to the system at each access point.
… no. of complete sets of Personal Protective Equipment PPE to be supplied with the system. Set to comprise - … no. of attachment devices x Removable Transfastener – Part number 85085. All to be supplied in a suitable PPE storage holdall
Installation: To BS 7883 by the system manufacturer or a contractor approved by the system manufacturer.
Structural anchors: Type recommended by the system manufacturer to suit the structure/ fabric into which they will be fixed
|
|
Latchways ManSafe ® for Protan Single Ply SE & G Membrane Roofing
|
|
Designed specifically for use on Protan warm metal deck roof systems, the Protan Constant Force post by Latchways is part of a ManSafe fall arrest system where a 8mm 7x7 316 grade stainless steel cable system is mounted at ankle height.
Anchorage device: Protan Constant Force™ post by Latchways for mechanical attachment through the insulation to the crowns of the steel deck, using Latchways toggle bolts. The post is unique through having a prefabricated and factory fitted Protan membrane sleeve, which is welded to the roof once the post is installed. It is fixed using four top fix toggle bolts which fix through to the metal deck allowing flexible system positioning. The post contains an integral energy absorber which deforms at a constant force in the event of a fall to prevent damage to the roof panel. Posts must be installed between 6 and 10 metres apart to guarantee a maximum load of 10kN onto the roof. The use of both internal and external corner units provides greater system flexibility.
Overall system length: This should comprise the roof perimeter system and single runs to allow access to gutters. Indicate if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Intermediate support spacing: Between 6 and 10m - as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Consult Latchways technical literature for details. Latchways plc can also provide a specification service mailto:%28spec@latchways.com) and it is recommended that they are consulted early in the design process.
It is recommended that the following clauses should also be included in the NBS specification for this system. N25/430, 460, 510, 520, 530, 550, 560, 570, 610, 640, 820 and 830.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
System reference: 210 Guided Type Fall Arrest System; Latchways ManSafe® for Protan Roofing Single Ply SE & G Membrane Roofing
Anchorage device: Protan Constant Force™ Post by Latchways
Finish: Polyester powder coated with a factory fitted Protan weathering sleeve in light or dark grey.
Colour: Light Grey / Dark Grey
Attachment: Mechanical attachment through the insulation to the crowns of the steel deck, using four Latchways top fix toggle bolts which fix through to the metal deck. The prefabricated and factory fitted Protan membrane sleeve, welded to the roof finish once the post is installed.
Overall system length: Specify length of system in metres comprising roof perimeter system and single runs to allow access to gutters. Specify if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Consult with Latchways for recommendations and details.
Intermediate support spacing: Between 6 and 10m and as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Accessories/ Other requirements:
System access: To be from … Consult with Latchways for recommendations and complete accordingly.
Completion: On completion of the installation, system to be inspected and fully tested and a test certificate covering a period of 12 months to be issued. Notice showing date and period of validity of the test certificate to be attached to the system at each access point.
… no. of complete sets of Personal Protective Equipment PPE to be supplied with the system. Set to comprise - … no. of attachment devices x Removable Transfastener – Part number 85085. All to be supplied in a suitable PPE storage holdall
Installation: To BS 7883 by the system manufacturer or a contractor approved by the system manufacturer.
Structural anchors: Type recommended by the system manufacturer to suit the structure/ fabric into which they will be fixed.
|
|
Latchways ManSafe® for Polymeric Single Ply Membrane Roofing
|
|
Designed specifically for single ply membrane roofing applications where a 8mm 7x7 316 grade stainless steel cable system is mounted at ankle height.
Anchorage device: Latchways Constant Force™ post for single ply roofing with mechanical attachment through the insulation to the crowns of the steel deck, using Latchways toggle bolts. The Constant Force™ posts, located on top of the membrane, are fixed with toggle bolts through the insulation to the metal tray allowing the system to be located anywhere on the roof. The post is made fully watertight with a membrane cover matching the roof which is sealed after installation. The Constant Force™ post contains an integral energy absorber which deforms at a constant force in the event of a fall to prevent damage to the roof panel. Posts must be installed between 6 and 10 metres apart to guarantee a maximum load of 10kN onto the roof. The use of both internal and external corner units provides greater system flexibility.
Overall system length: This should comprise the roof perimeter system and single runs to allow access to gutters. Indicate if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Intermediate support spacing: Between 6 and 10m - as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Consult Latchways technical literature for details. Latchways plc can also provide a specification service mailto:%28spec@latchways.com) and it is recommended that they are consulted early in the design process.
It is recommended that the following clauses should also be included in the NBS specification for this system. N25/430, 460, 510, 520, 530, 550, 560, 570, 610, 640, 820 and 830.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
System reference: 210 Guided Type Fall Arrest System; Latchways ManSafe® for Polymeric Single Ply Roofing
Anchorage device: Latchways Constant Force™ Post for single ply roofing
Finish: Polyester powder coated.
Colour: Grey
Attachment: Mechanical attachment through the insulation to the crowns of the steel deck, using four Latchways toggle bolts which fix through to the metal tray. The post to be made fully watertight with a membrane cover matching the roof covering and sealed after installation.
Overall system length: Specify length of system in metres comprising roof perimeter system and single runs to allow access to gutters. Specify if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Consult with Latchways for recommendations and details.
Intermediate support spacing: Between 6 and 10m and as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Accessories/ Other requirements:
System access: To be from … Consult with Latchways for recommendations and complete accordingly.
Completion: On completion of the installation, system to be inspected and fully tested and a test certificate covering a period of 12 months to be issued. Notice showing date and period of validity of the test certificate to be attached to the system at each access point.
… no. of complete sets of Personal Protective Equipment PPE to be supplied with the system. Set to comprise - … no. of attachment devices x Removable Transfastener – Part number 85085. All to be supplied in a suitable PPE storage holdall
Installation: To BS 7883 by the system manufacturer or a contractor approved by the system manufacturer.
Structural anchors: Type recommended by the system manufacturer to suit the structure/ fabric into which they will be fixed
|
|
Latchways ManSafe® Systems for Standing Seam Roofing
|
|
Designed specifically for standing seam roofing applications where a 8mm 7x7 316 grade stainless steel cable system is mounted at ankle height.
Anchorage device: Latchways Constant Force post™ for attachment to bulb type standing seam using 4no. Latchways split clamps per post. The system is attached to the standing seams of the roof panels via Constant Force™ posts. The use of non-penetrative split clamps on the standing seam allows the posts to be located anywhere on the roof panel between two seams. The post is powder coated in neutral silver as standard and contains an integral energy absorber, which deforms at a constant force in the event of a fall to prevent damage to the roof panel. Posts must be installed between 6 and 10 metres apart to guarantee a maximum load of 10kN onto the roof. The use of both internal and external corner units provides greater system flexibility.
Overall system length: This should comprise the roof perimeter system and single runs to allow access to gutters. Indicate if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Intermediate support spacing: Between 6 and 10m - as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Consult Latchways technical literature for details. Latchways plc can also provide a specification service mailto:%28spec@latchways.com) and it is recommended that they are consulted early in the design process.
It is recommended that the following clauses should also be included in the NBS specification for this system. N25/430, 460, 510, 520, 530, 550, 560, 570, 610, 640, 820 and 830.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
System reference: 210 Guided Type Fall Arrest System; Latchways ManSafe® for Standing Seam Roofing
Anchorage device: Latchways Constant Force™ Post for bulb type standing seam roofing.
Finish: Polyester powder coated.
Colour: Neutral Silver
Attachment: Mechanical attachment using 4no. Latchways split clamps per post which locate over the standing seam.
Overall system length: Specify length of system in metres comprising roof perimeter system and single runs to allow access to gutters. Specify if the system is to provide access for roof light cleaning, roof inspection and gutter cleaning etc.
Consult with Latchways for recommendations and details.
Intermediate support spacing: Between 6 and 10m and as designed by the Latchways approved installer to meet the requirements of the Latchways ManSafe design software.
Accessories/ Other requirements:
System access: To be from … Consult with Latchways for recommendations and complete accordingly.
Completion: On completion of the installation, system to be inspected and fully tested and a test certificate covering a period of 12 months to be issued. Notice showing date and period of validity of the test certificate to be attached to the system at each access point.
… no. of complete sets of Personal Protective Equipment PPE to be supplied with the system. Set to comprise - … no. of attachment devices x Removable Transfastener – Part number 85085. All to be supplied in a suitable PPE storage holdall
Installation: To BS 7883 by the system manufacturer or a contractor approved by the system manufacturer.
Structural anchors: Type recommended by the system manufacturer to suit the structure/ fabric into which they will be fixed
|
|
Latchways ManSafe® Systems For Ladders
|
|
Latchways cable based ManSafe systems for Ladders provide continuous fall protection when climbing or descending a fixed industrial ladder. The system can be planned at the design stage or added to existing structures and will operate smoothly in all environmental conditions.
The ManSafe system for ladders can be rung or stringer mounted and incorporates a tensioning device and cable clamp which allows simple swage free installation and indicates when the correct tension is reached. The system does not require any fixing holes to be made into the structure, as it clamps on to the rung or stringer. The LadderLatch™ unit passes freely over intermediate cable supports and can be detached or attached at any point on the ladder where it is safe to do so. Intermediate wire guides should be positioned at maximum 4 metres spacings up to 55metres, and every 2 to 3 metres above 55 metres high.
Consult Latchways technical literature for details. Latchways plc can also provide a specification service mailto:%28spec@latchways.com) and it is recommended that they are consulted early in the design process.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
System reference: Latchways ManSafe® Systems for Ladder
|
|
N25 PERMANENT ACCESS AND SAFETY EQUIPMENT
220 SINGLE POINT ANCHORAGE DEVICES FOR FALL ARREST
|
|
Latchways PushLock System
Latchways plc offers a complete service in the provision of fall protection equipment for a wide range of applications.
The PushLock system consists of a stainless steel socket and removable eyebolt to provide anchorage points for the attachment of PPE. The eyebolt is removed when not in use, minimising visual impact. The remaining socket cap can be colour coded to match interior décor or metalwork. Various sockets are available for fixing mechanically or chemically into different structures such as steelwork, masonry, brickwork and cavity walls.
Consult Latchways plc technical literature for details. Latchways plc can also provide a specification service and it is recommended that they are consulted early in the design process.
Manufacturer: Latchways plc, Hopton Park , Devizes Wiltshire SN10 2JP Tel: +44 (0)1380 732700 Fax: +44 (0)1380 732701 E-mail: info@latchways.com Web: http://www.nbsplus.co.uk/process.asp?Latchways
Product reference: Latchways PushLock System
|
|