Installation procedure


Locating template Locate position of post, ensuring correct orientation of template relative to roof peaks and system design.	Drilling Once you have located the position of the post, mark each edge position of the template on the roof sheet with a marker pen, then drill the fixing holes using the drilling template provided (part no: 65626-00). After removing the template, it is recommended that all holes drilled into the roof are treated with a protective laquer, prior to fitting the post.	Cleaning Ensure the area of the base plate and roof where attachment will take place are cleansed with alcohol based solution then: Attach two sealing strips to the underside of post, covering the fixing areas to be used, ensuring the tape protrudes 5 mm below the edge of the plate. The tape forms the seal between the plate and the roof.	Tape Re-check you have the correct position before fixing the post to roof.

Position the post Aligning one side with pen marks, insert 2 rivets, one at either end and align with holes. Drop other side of base plate onto the other crown, making sure it aligns with the marks. Press down until base plate snaps into place.	Fixing Secure post to roof using all the 20 bulb tite rivets supplied by Latchways. The rivets are correctly fixed using a rivet tool supplied by Gesipa Systems Ltd (part no’s: 7120028, 7130028 or 7250037).	End posts On both end posts a D ring should be attached using a single M12 bolt. It should be tightened to a torque of typically 20 Nm, ensuring that the spring washer is flat.	Intermediate posts On the intermediate post attach the cable support with an M12 bolt, tightened to a torque of typically 20 Nm, ensuring that the spring washer is flat. Ensure the D ring and hanger bracket are placed in the correct orientation for the cable to pass through.

Corner posts On the corner post fix a corner unit with an M12 bolt tightened to a torque of typically 20 Nm, so that the spring washer is flat. Ensure the unit is orientated in the correct direction for system use.	Variable posts The variable bracket should be bent using the tube bending tool supplied by Latchways (part no: 85170). NB: It is recommended that the variable bracket should only be bent when the cable has been threaded through the tube. Slide the tube bending tool along the arm of the bracket to the point where a bend is required and tighten by twisting the bar on the top. A maximum angle change of 40° is achieved on each end of the bracket. To attach to the post follow the instructions in point 9.	Fix the swageless terminal to yoke Fit the swageless terminal according to the instructions supplied with the post. NB: If tension adjustment is required at both ends of the system, fit a threaded swageless termination to line tenser, as supplied with the alternative end sets.	First end post Attach the swageless terminal to yoke: Remove the clevis pin and attachyoke to D ring securing by replacing the clevis pin. Fit the split pin and open arms out fully.

Thread the cable When all posts and bracketry are installed, thread the cable through the support brackets, checking that it is not twisted and is free from kinks. Ensure that the cable is threaded through all necessary brackets such as hangers and corner brackets.	Second end post Fit the long run line tenser, turnbuckle and swageless terminal unit to the D ring, ensuring that there is the maximum adjustment available in the turnbuckle. Fit the split pin and open arms out fully.	Cut the cable Remove the cable slack from the system, mark the position for cutting and cut the cable to length.	Connect the system Remove the swageless terminal from the turnbuckle body and attach to cable as per instructions provided. When the cable is locked in place, re-attach to the turnbuckle.

Tension the system Twist the turnbuckle to tension the system.	Check system tension The correct pre-tension is acheived when the disk can be turned freely with your fingers. If this is not the case then the system will need to be adjusted prior to use. When the correct pre-tension has been achieved, fit split pins to the long run line tenser and the swageless terminal to prevent the turning of the turnbuckle and also maintaining system pre-tension. Always check the tension indicator before system use.